Electronics Engineer

Summary

This position is with the U. S. Department of Labor, Occupational Safety and Health Administration (OSHA), in the Directorate of Technical Support and Emergency Management (DTSEM), Division of Engineering Services, located in Sandy, UT. This position has a full performance level of GS-12. This position is inside the bargaining unit. Additional selections may be made from this job announcement. This position is NOT remote. Selectee will be expected to report to the office listed above.

Duties

Duties for the Electronics Engineer include, but are not limited to: Performing repair and calibration of OSHA instrumentation and equipment as needed and reviewing the adequacy of field instruments for enforcement of OSHA standards. Preparing and presenting written and oral reports in a clear and concise manner to scientific and professional audiences when appropriate. Developing and maintaining the necessary software for operation and control of computer-operated or -assisted calibration systems. Providing technical assistance to technicians. Assist the supervisory engineer in training junior technicians to use, calibrate, and repair electronic instruments and their calibration systems. As the employee progresses, the assignments will become more difficult and complex with less supervision.

Qualifications

THE ENGINEER SERIES HAS AN INDIVIDUAL OCCUPATIONAL REQUIREMENT. ALL APPLICANTS MUST MEET THIS REQUIREMENT IN ORDER TO BE CONSIDERED. You must meet the "Individual Occupational Requirement" and the "Specialized Experience" as described below, to qualify for the Electronics Engineer position. INDIVIDUAL OCCUPATIONAL REQUIREMENT (IOR):A. Degree: Bachelor's degree (or higher degree) in engineering. To be acceptable, the program must: (1) lead to a bachelor's degree (or higher degree) in a school of engineering with at least one program accredited by the Accreditation Board for Engineering and Technology (ABET); OR (2) include differential and integral calculus and courses (more advanced than first-year physics and chemistry) in five of the following seven areas of engineering science or physics: (a) statics, dynamics; (b) strength of materials (stress-strain relationships); (c) fluid mechanics, hydraulics; (d) thermodynamics; (e) electrical fields and circuits; (f) nature and properties of materials (relating particle and aggregate structure to properties); and (g) any other comparable area of fundamental engineering science or physics, such as optics, heat transfer, soil mechanics, or electronics. OR B. Combination of Education and Experience: College-level education, training, and/or technical experience that furnished (1) a thorough knowledge of the physical and mathematical sciences underlying engineering, and (2) a good understanding, both theoretical and practical, of the engineering sciences and techniques and their applications to one of the branches of engineering. The adequacy of such background must be demonstrated by one of the following:1. Professional registration or licensure - Current registration as an Engineer Intern (EI), Engineer in Training (EIT), or licensure as a Professional Engineer (PE) by any State, the District of Columbia, Guam, or Puerto Rico. Absent other means of qualifying under this standard, those applicants who achieved such registration by means other than written test (e.g., State grandfather or eminence provisions) are eligible only for positions that are within or closely related to the specialty field of their registration. For example, an applicant who attains registration through a State Board's eminence provision as a manufacturing engineer typically would be rated eligible only for manufacturing engineering positions.2. Written Test - Evidence of having successfully passed the Fundamentals of Engineering (FE) examination, or any other written test required for professional registration, by an engineering licensure board in the various States, the District of Columbia, Guam, or Puerto Rico.3. Specified academic courses - Successful completion of at least 60 semester hours of courses in the physical, mathematical, and engineering sciences and that included the courses specified in A above. The courses must be fully acceptable toward meeting the requirements of an engineering program.4. Related curriculum - Successful completion of a curriculum leading to a bachelor's degree in an appropriate scientific field, e.g., engineering technology, physics, chemistry, architecture, computer science, mathematics, hydrology, or geology, may be accepted in lieu of a degree in engineering, provided the applicant has had at least 1 year of professional engineering experience acquired under professional engineering supervision and guidance. Ordinarily there should be either an established plan of intensive training to develop professional engineering competence, or several years of prior professional engineering-type experience, e.g., in interdisciplinary positions. In addition to meeting the Individual Occupational Requirement (IOR), applicants must meet the following specialized experience: Applicants must have 52 weeks of specialized experience equivalent to at least the next lower grade level, GS-9 in the Federal Service. Specialized Experience is the experience that equipped the applicant with the particular knowledge, skills, and abilities (KSA's) to perform the duties of the position successfully, and that is typically in or related to the position to be filled. To be creditable, specialized experience must have been equivalent to at least the next lower grade level. Qualifying specialized experience for GS-11 includes: Participating in technical training in the area of calibration procedures or other technically related activities. Assisting in the design of electronic circuit modifications. Developing, implementing or troubleshooting mechanical and/or electronic systems used for calibration. Implementing quality control and/or quality assurance programs for the calibration of equipment. OR Education: Ph.D. or equivalent doctoral degree or 3 full years of progressively higher-level graduate education leading to such a degree in a field which demonstrates the knowledge, skills, and abilities necessary to do the work of the position, such as General Engineering; Mechanical Engineering; Electronics Engineering; or Electrical Engineering. (Note: You must attach a copy of your transcripts.) OR Combination of Education and Experience: A combination of education and experience may be used to qualify for this position.

Education

Any applicant falsely claiming an academic degree from an accredited school will be subject to actions ranging from disqualification from federal employment to removal from federal service. If your education was completed at a foreign college or university, you must show comparability to education received in accredited educational institutions in the United States and comparability to applicable minimum coursework requirements for this position. Click Evaluation of Foreign Education for more information.