Seatrium
Senior Process Engineer
Seatrium (SG) Pte. Ltd.
Get past the screening software and onto a recruiter's desk
hirly rewrites your resume for this job — matching the keywords and skills in the posting, moving your most relevant experience to the top, and writing a cover letter to fit. About 30 seconds.
- Keywords matched to this posting
- Fit score before you apply
- Cover letter included
Matched against 2.4M live jobs from 200,000+ employers in 200+ countries.
Tailor my resume for this job →Apply from your AI assistant
Connect hirly to Claude and ask it to apply to this job. hirly tailors your resume, fills the employer’s form and asks before sending. ChatGPT: manual setup today.
Some employer sites stop an application at a CAPTCHA or sign-in and hand it back with a link. Applying needs a paid plan. Works with any assistant that supports MCP.
hirly's read of this role
- Seniority
- Senior
- Country
- SG
- Work mode
- On-site / unstated
- First seen by hirly
- 27 Sept 2026
Derived automatically from the posting. Upload your resume above to see how the role scores against it.
the posting
JOB DESCRIPTION
- Understand the Project & Client’s Contractual requirements and scope of work. Clarify scope of work and supply to form the contract basis with Client.
- Support Project Management Team on Process deliverable schedule updates.
- Preparation of Process Philosophies not limited to Control and shutdown philosophy, Preparation of Isolation philosophy, Sparing philosophy, P&ID philosophy, and Vent, Relief, and Flare load calculation philosophy.
- Responsible to prepare Development of Process Simulation Heat and Mass Balances (H&M Sheets).
- Responsible for preparation of Process Flow Diagram (PFD), Utility Flow Diagram (UFD) and Piping & Instrumentation Diagram (P& ID), Cause and Effect Diagrams and Safe chart.
- Perform Equipment Sizing Calculations (Separators, Vessels, Storage tanks etc.), Line Sizing Calculations and Hydraulic Analysis and Flare Network design.
- Responsible for preparing and reviewing technical queries and Assist Lead engineer conclude TQs with Client.
- Perform process studies like Dynamic Depressurization study.
- Preparation of reports, not limited to Process System design report, vent and drain report, Utility summary.
- Preparation of Process datasheets for Mechanical Equipment and Instruments.
- Co-ordinate with the other disciplinary departments in terms of process inputs.
- Responsible for Inter disciplinary checks and provide input to other discipline engineering deliverables like Mechanical Equipment List (MEL), Electrical Load List, Topsides Weight report, Mechanical and Instrument datasheets, other discipline critical philosophies, etc. as required.
- Review Vendor documents and provide comments to ensure the vendor design is in line with the project requirements.
- Responsible for updating Third Party Specialist, Process & Safety studies, including follow through of all such studies (review study reports, attending workshops, etc.)
- Assist Lead engineer for managing interface with hull and marine systems such as Cargo, Utilities, etc.
- Provide input to Operating manual, Pre-commissioning and commissioning manual.
- Attend project meetings as required (intra-discipline; Client, inter-discipline, SCM and Sub-contractor / vendor / 3rd Party) to assist lead engineer to address / clarify engineering issues and progress; and follow-through with meeting actions.
- Assist Lead engineer for identifying all Client's comments and communications, to ensure Client's comments / requirements are implemented, as well as feedback to Project Management and Commercial team, raise trends / potential change orders, as necessary.
- Assist Lead engineer for project process engineering support through after Engineering kick start through Detail Engineering / As-Built Engineering / Pre-Commissioning and Commissioning / Warranty Test Run, as required and as per project requirements.
- Responsible for process design data collection, analysis and maintenance to support project feasibility studies, preparation of tender/ construction documents as well as basic and detailed design drawings
- Assembles process design engineered submittal manuals/ booklets including drawings, schematics, documents, reports, calculations, etc. and provides copying support for contractors/ customers
- Liaises with package engineer to obtain updated information, when required and maintains process design submittal filing system in the engineering reference library
- Prepares process design project training manuals and owner’s manuals for on-site training to contractors and customers
- Monitors and follows up changes updated by junior team members on the operational process project drawings and records as well as the lessons learnt compiled during project execution
JOB REQUIREMENTS
- Bachelor’s degree in chemical engineering, or related engineering disciplines.
- 10 years of design working experience in Offshore industry.
- Experience in FEED and EPC engineering, preferable in FPSO industry.
- Able to multi-task and able to work in a fast-paced environment.
BUSINESS UNIT
Seatrium Limited
Similar jobs
- Senior Process EngineerPfizer · Singapore - TuasFirst seen 6d ago
- Senior /Associate Engineer Process Engineer (Thin Film/CVD/PVD/CMP)Globalfoundries · SGP - WoodlandsFirst seen 6d ago
- Sr Engineer Process EngineeringGlobalfoundries · SingaporeFirst seen 6d ago
- Principal Process EngineerKbr · Singapore, SingaporeFirst seen yesterday
- Senior Principal Process EngineerKbr · Singapore, SingaporeFirst seen yesterday
Browse similar roles
Want this one?
Upload your resume and hirly rewrites it for this job and writes the cover letter — in about thirty seconds, before you sign up.
Tailor my resume for this job